HSCL 00xx

This section lists the HSCL 00xx error codes.

Note: The following error messages and recovery actions might include procedures that are not available on the DS8000® management console. If in doubt, contact the next level of support. If you are instructed to shut down the management console, then you must first verify that the customer is not currently performing DS8000 actions through the management console ESSNI connection.
Table 1. HSCL 00xx: Profile data error codes
Error code Message Recovery action
0003 The profile data save area is full. Remove any profiles that are no longer needed. Remove the profiles that are no longer needed.
0004 A profile with name {0} already exists in the partition with ID {1} in the profile data of the managed system. Provide another name for this profile. Rename the profile to a name that is not already in use in this partition.
0005 Cannot find information regarding profile data of the managed system. Run a rebuild managed system operation.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0006 The managed system's profile data has been corrupted. You must either restore or reinitialize the profile data. You must restore the profile data. See MAP6630 Recovering partition data on a CEC enclosure for details.
0007 The profile data of the managed system cannot be accessed or modified. Run a rebuild managed system operation.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0008 Could not construct or initialize profile data. Rebuild the managed system. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
0009 Could not construct or initialize the profile data from the backup file, {0}. Repeat the operation.
  1. Repeat the operation.
  2. If the problem persists, see MAP6630 Recovering partition data on a CEC enclosure.
  3. If the problem persists, contact your next level of support.
000A Could not build the profile for the managed system. Repeat the operation.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
000B Could not get the activated LPAR profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
000C Could not get the activated system profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
000D Could not get all the system profiles from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
000E Could not get the default LPAR profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
000F Could not get the default system profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0010 Could not get the LPAR profiles for the partition from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0011 Could not get the LPAR profiles for the partition from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0012 Could not get the system profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0013 Could not remove the LPAR profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0014 Could not remove the system profile from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0115 Could not save the LPAR profile to the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0016 Could not save the system profile to the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0017 Could not create the LPAR profile in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0018 Could not create the system profile in the profile data. Rebuild the managed system
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0019 Could not set the activated LPAR profile in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
001A Could not set the activated system profile in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
001B Could not set the default LPAR profile in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
001C Could not set the default system profile in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
001D Could not clean up the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
001E Could not update the profile data cache. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
001F Could not check for duplicate LPAR name. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0020 Could not remove the LPAR profile from the system profile content in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0021 Could not add the LPAR profile to the system profile in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0022 Could not get the partition name from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0023 Could not get all the partition names from the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0024 Could not set the partition name in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0025 Could not build the profile data from the local file, {0}. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0026 Could not write the data to the managed system. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0027 Could not back up the profile data to a file. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0028 Could not read profile data from the managed system. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0029 Could not delete profiles at the partition with ID of {0} in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
002A Could not modify the system profiles containing the LPAR slot ID of {0} in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
002B Could not perform a priority restore on the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
002C Could not merge the profile information in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
002D Could not merge partition name data in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
002E Could not merge default and activated list data in the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0030 Could not initialize the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0031 The profile data has been cleared. Either restore or reinitialize the profile data save area.
  1. Restore the profile data. See MAP6630 Recovering partition data on a CEC enclosure.
  2. If the problem persists, contact your next level of support.
0032 Could not set the system profile's user-defined name to the profile data. Rebuild the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0033 This managed system version, {0}, is unknown to management console. Update to a management console release that can handle this version of managed system.
  1. Perform the rebuild managed system operation. See MAP6620 Rebuilding managed system information for details.
  2. If the same error occurs, update to a management console release that can handle this version of managed system.
  3. If you are not sure what version to use, contact your next level of support.
0034 The levels of managed system and profile data area are not matching up. Managed system version: {0}, profile data area version: {1}. Upgrade the managed system version "to proper level."
  1. Rebuild managed system operation. See MAP6620 Rebuilding managed system information for details.
  2. If the same error occurs, update the managed system to a proper version.
  3. If you are not sure what version to use, contact your next level of support.
0035 Cannot restore profile data with two different versions of profile save data.
  1. Perform the operation again.
  2. If the same error occurs, restore by using another profile data file. See MAP6630 Recovering partition data on a CEC enclosure.
  3. If the problem persists, contact your next level of support.
0036 Migrate profile data failed.
  1. Perform the operation again.
  2. If the problem persists, contact your next level of support.
0037 This level of profile data, {0}, is unknown to this management console. Update to a management console version that can handle this level of profile data.
  1. Perform the operation again.
  2. If the problem persists, update to a management console version that can handle this level of profile data.
  3. If you are not sure what version to use, contact your next level of support.
0038 Creation of logical partition profiles failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support.
0039 Deletion of logical partitions failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support.
003A Removal of system profiles failed at profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support.
003B Setting of partition information failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support.
003C Retrieval of all logical partition information failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support.
003D Retrieval of partition information failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the operation.
  3. If the problem persists, contact your next level of support.
0041 Migration of partition information failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0042 Migration of profile names failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0043 Migration of default profile list failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0044 Migration of activated profile list failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0046 Migration of I/O unit and profile information failed in the profile data save area.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0047 Migration of time stamps of profile data save area failed.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0048 Migration of checksums of the profile data save area failed.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.
0049 Unable to get next available profile ID from the management console profile data.  
004A Management console Save Area Set Fast Activation failed.  
004B Management console Save Area Get Fast Activation failed.  
004C Unable to open the management console Save Area file.  
004D The management console could not retrieve information from the managed system.  
004E Unable to set partition information in the profile data. Execute a rebuild managed system operation.  
004F Management console Save Area Get System Credential Information failed.  
0050 Management console Save Area Set System Credential Information failed.  
0051 Cannot retrieve Virtual Ethernet MAC Address prefix.
  1. Try the operation again.
  2. If the problem persists, contact IBM support.
0052 Cannot set Virtual Ethernet MAC Address Prefix.
  1. Try the operation again.
  2. If the problem persists, contact IBM support.
0053 Attempt to update profile information failed due to invalid resource lock type.
  1. Try the operation again.
  2. If the problem persists, contact IBM support.