HSCL 03xx

This section lists the HSCL 03xx error codes.

Note: The following error messages and recovery actions might include procedures that are not available on the DS8000® management console. If in doubt, contact the next level of support. If you are instructed to shut down the management console, then you must first verify that the customer is not currently performing DS8000 actions through the management console ESSNI connection.
Table 1. HSCL: 03xx managed system resource error codes
Error code Message Recovery action
03EA There is an insufficient number of processors: Obtained - {0}, Required - {1}. Check that there are enough processors available to activate the partition. If not, create a new profile or modify the existing profile with the available resources, and then activate the partition. If the partition must be activated with the specified number of processors, deactivate any active logical partitions using the resource, and then activate the partition.
  1. Check the managed system properties window to ensure that enough processors are available to activate the partition.
  2. If there are not enough processors available, create a new profile or modify the existing profile with the available resources. Then activate the partition.
  3. If the partition must be activated at any cost, deactivate any running partition that is using the resource and then activate the partition.
  4. If the problem persists, contact your next level of support.
03EB Could not allocate the I/O slot for activation in {0}. Check that the specified I/O is available to activate the partition. If not, create a new profile or modify the existing profile with the available resources, and then activate the partition. If the partition must be activated with these resources, deactivate any running partitions using the resource, and then activate this partition.
  1. Check the managed system properties window to ensure that enough I/O slots are available to activate the partition.
  2. If there are not enough I/O slots available, create a new profile or modify the existing profile with the available resources. Then activate the partition.
  3. If the partition must be activated at any cost, deactivate any running partition that is using the resource and then activate the partition.
    Note: If you have tried to recover using the above action and you are not successful, and you must activate the partition, edit the profile for the partition you are activating and remove all slots that are associated with the identified slot's PHB. See the PCI Adapter Placement Reference, order number SA38-0538 for information on PHB slot associations.
  4. If the problem persists, contact your next level of support.
03EC There is not enough memory: Obtained - {0}, Required - {1}. Check that there is enough memory available to activate the partition. If not, create a new profile or modify the existing profile with the available resources, and then activate the partition. If the partition must be activated with these resources, deactivate any running partition or partitions using the resource, and then activate this partition.
  1. Check the managed system properties window to ensure that enough memory is available to activate the partition.
  2. If there is not enough available memory, create a new profile or modify the existing profile with the available resources and then activate the partition.
  3. If the partition must be activated at any cost, deactivate any running partition using the resource, and activate the partition.
  4. If the problem persists, contact your next level of support.
03ED The I/O unit specified by this ID cannot be found and might have been deleted from the managed system. Modify the profile. Modify the partition profile so that the unit that cannot be found is no longer part of the profile's resources.
03EE The specified slot number cannot be found. Ensure the profile is not using I/O unit slots that do not exist in the managed system. The adapter specified cannot be found. Modify partition profiles so that the slot that cannot be found is not part of any partition profile.
03EF The number of system units, slots, and I/O required and desired information stored in the properties do not match. The profile might be corrupted. Perform the Restore Profile Data task.
  1. The profile might be corrupted. Restore the profile data. See MAP6660 Operation procedures that do not apply to DS8000 for details.
  2. If the problem persists, delete the profile and create a new profile.
03F0 Could not allocate the I/O slot for activation in I/O drawer {0}. Slot {1} is currently being used by another partition. Perform one of the following three actions: 1) Remove this I/O slot from the profile, 2) Change the I/O slot from Required to Desired in the profile, or 3) Remove the I/O slot from the other partition.
Perform one of the following actions:

  • Remove this I/O slot from the profile.
  • Change the I/O slot from Required to Desired in the profile.
  • Remove the I/O slot from the other partition.
03F4 Not enough processing resources to meet the allocation setting
  1. Ensure there is enough processors to start the partition.
  2. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  3. If the problem persists, contact your next level of support.
03F5 There is an insufficient amount of shared processing resources: Virtual processor obtained - {0}, processing units obtained - {1}, Required virtual processors - {2}, Required processing units - {3}. Check that there is enough processing resources available to activate the partition. If not, create a new profile or modify the existing profile with the available resources, and then activate the partition. If the partition must be activated with the specified amount of processing resources, deactivate any active partitions using the resource then activate this partition.
  1. Ensure there is enough processing to start the partition.
  2. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  3. If the problem persists, contact your next level of support.
03F6 The 5250 CPW needed by the partition exceeds the system limit. Amount allowable at this point is {0}.
  1. Check the 5250 CPW.
  2. If the problem persists, contact your next level of support.
03F7 Insufficient amount of 5250 CPW for allocation: Obtained - {0}, required - {1}.
  1. Ensure there are enough 5250 CPW to start the partition.
  2. Rebuild managed system. See MAP6620 Rebuilding managed system information for details.
  3. If the problem persists, contact your next level of support.
03F8 The 5250 CPW set by user is below the partition minimum allowed: minimum = {0}.
  1. Ensure the 5250 CPW setting is correct.
  2. If the problem persists, contact your next level of support.
03F9 Not enough memory resources to meet the allocation setting.
  1. Ensure there is enough memory to start the partition.
  2. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  3. If the problem persists, contact your next level of support.
03FA Unable to gather I/O information of the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the task.
  3. If the problem persists, contact your next level of support.
03FB Unable to gather virtual I/O information of the managed system.
  1. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  2. Retry the task.
  3. If the problem persists, contact your next level of support.
03FC The MAC address prefix specified was not valid. The MAC address prefix must be six characters long, and only contain hexadecimal values (0-9 and A-F).
  1. Ensure the MAC address conform with the rule specified.
  2. If the problem persists, contact your next level of support.
03FD The MAC address prefix cannot have the multicast bit on. The multicast bit is 0x010000.
  1. Ensure the multicast bit is not on.
  2. If the problem persists, contact your next level of support.
03FE There was an error updating a virtual Ethernet adapter MAC address.
  1. Retry the task.
  2. If the problem persists, contact your next level of support.
03FF Failed to extract system resources information. Ensure the managed system is powered on.
  1. Retry the task.
  2. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details.
  3. If the problem persists, contact your next level of support.