HSCL 11xx

This section lists the HSCL 11xx error codes.

Note: The following error messages and recovery actions might include procedures that are not available on the DS8000® management console. If in doubt, contact the next level of support. If you are instructed to shut down the management console, then you must first verify that the customer is not currently performing DS8000 actions through the management console ESSNI connection.
Table 1. HSCL: 11xx backup and restore error codes
Error code Message Recovery action
1195 Unable to back up the profile data to the backup file. Try again.
  1. Try the task again.
  2. If the problem persists, contact your next level of support.
1196 You do not have read access permission on the backup file {0}. Refresh the interface and check whether the operation was completed. If not, try the operation again.
  1. Try the task again.
  2. If the operation still fails, contact your next level of support.
1197 Unable to read the profile data's backup file {0}. Refresh the interface and check whether the operation was completed. If not, try the operation again.
  1. Try the task again.
  2. Shut down and restart the management console, and then try the task again.
  3. If the operation still fails, contact your next level of support.
1198 Cannot find backup file {0} for profile data. Select a valid, existing backup file.
  1. Try the task again.
  2. If the operation still fails, contact your next level of support.
1199 A full restore is not permitted when there are logical partitions in {0} state. A full restore can only be issued when the managed system was powered on and all partitions are in the Not Activated state.
  1. Verify the managed system was powered-on to run in Partition Standby.
  2. Try the task again.
  3. If the operation still fails, contact your next level of support.
119A There was an I/O error while backing up the profile data. Try again.
  1. Try the task again.
  2. Shut down and restart the management console, and then try the task again.
  3. If the operation still fails, contact your next level of support.
119B The restore profile data operation failed. Try again.
  1. Try the task again.
  2. Shut down and restart the management console, and then try the task again.
  3. If the operation still fails, contact your next level of support.
119C Cannot initialize profile data when the managed system was not in the Standby or Operating state, or there is any partition not in the Not Activated state.
  1. Verify that the managed system is in the Standby or Operating state, and that no logical partitions are running.
  2. Try the task again.
  3. If the problem persists, contact your next level of support.
119D Cannot restore the profile data if the managed system is in the {0} state.
  1. Verify that the managed system is in the Standby or Ready state, and try the task again.
  2. If the problem persists, contact your next level of support.
119E Cannot initialize the profile data if the managed system is in the {0} state.
  1. Verify that the managed system is in the Standby or Ready state, and try the task again.
  2. If the problem persists, contact your next level of support.
119F The backup file {0} used to restore the profile data is not valid. Its file size ({1}) is not correct. Select a valid backup file.
The backup file selected is not valid. The
file might be corrupted.

  1. Try the task again. Select another backup file and try the task again.
  2. If the problem persists, contact your next level of support
11A0 Cannot restore the profile data if the managed system is in the {0} state. The managed system must be in the Operating or Standby state.
  1. Verify that the managed system is in Operating or Standby state.
  2. Try the task again.
11A1 Cannot initialize the profile data if the managed system is in the {0} state. The managed system must be in the Operating or Standby state.
  1. Verify that the managed system is in Operating or Standby state.
  2. Try the task again.
11A2 Could not display the backup dialog for the managed system: {0}. Try the operation again.
  1. Try the task again.
  2. Log off the management console, and then log back in.
  3. Try the task again.
  4. If the problem persists, contact your next level of support.
11A3 Could not back up the profile data for the managed system: {0} to file {1}.
  1. Refresh the graphical user interface. See MAP6620 Rebuilding managed system information for details.
  2. Try the task again.
  3. Shut down and restart the management console, and then try the task again.
  4. If the problem persists, contact your next level of support.
11A4 Cannot back up profile data to the default backup file name {0}. Cannot back up the profile data to the default backup file. Choose a different backup file name. If the problem persists, contact your next level of support.
11A5 Could not display the remove backup dialog for the managed system {0}. Try again.
  1. Try the task again.
  2. Log off the management console, and log back in.
  3. Try the task again.
  4. Contact your next level of support.
11A6 Could not remove the backup file {0} from the managed system {1}.
  1. Refresh the graphical user interface. See Updating managed system or frame information for details.
  2. Try the task again.
  3. Shut down and restart the management console, and then try the task again.
  4. If the problem persists, contact your next level of support.
11A7 No backup file has been selected for the operation. Select a backup file. If the problem persists, contact your next level of support.
11A8 Could not display the restore profile data dialog for the managed system: {0}. Try the operation again.
  1. Try the task again.
  2. Log off the management console, and then log back in.
  3. Try the task again.
  4. If the problem persists, contact your next level of support.
11A9 Could not initialize the profile data task on the managed system {0}. Refresh the interface and check whether the operation was performed. If not, try the operation again.
  1. Refresh the graphical user interface. See MAP6620 Rebuilding managed system information for details.
  2. Ensure the operation has been performed and displays on the graphical user interface.
  3. If not, repeat the operation.
  4. If the problem persists, contact your next level of support.
11AA Could not restore the profile data task on the managed system {0} with backup file {1} of {2} option. Refresh the interface and check whether the operation was performed. If not, try the operation again.
  1. Refresh the graphical user interface. See MAP6620 Rebuilding managed system information for details.
  2. Try the task again.
  3. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details. Then try the task again.
  4. If the problem persists, contact your next level of support.
11AB Could not display the recover partition data dialog for the managed system {0}.
  1. Try the task again.
  2. Log off the management console, and then log back in.
  3. Try the task again.
  4. If the problem persists, contact your next level of support.
11AC Could not perform the recover logical partition data task on the managed system {0}.
  1. Refresh the graphical user interface. See MAP6620 Rebuilding managed system information for details.
  2. Try the task again.
  3. Rebuild the managed system. See MAP6620 Rebuilding managed system information for details. Then try the task again.
  4. If the problem persists, contact your next level of support.
11AD Could not display the Rebuild Computer System dialog for managed system {0}.
  1. Refresh the graphical user interface and retry the operation. See MAP6620 Rebuilding managed system information for details.
  2. If the problem persists, contact your next level of support.