SRNs 700-xxx through 7C1-117
Note: Some SRNs in this chapter might have 4 rather than 3 digits
after the dash (-).
| Service Request Number | Failing Function Codes | Description/Action (Unless indicated otherwise use MAP0210 General problem resolution) |
|---|---|---|
| 700-xxx
to 707-xxx |
See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 721-xxx | See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 722-xxx | 722 | Unknown disk drive type is failing. Action: MAP0210 General problem resolution. |
| 723-xxx | 723 | Unknown CD-ROM type is failing. Action: MAP0210 General problem resolution. |
| 724-xxx | 724 | Unknown tape drive failure. Action: MAP0210 General problem resolution. |
| 733-110
to 733-120 |
733 | The Reserve command failed, or the Inquiry command failed. Action: MAP0210 General problem resolution. |
| 733-130
to 733-135 |
733
media |
The Load command failed, or the Unload command failed. Action: MAP0210 General problem resolution. |
| 733-140 | 733 | The Mode Select command failed. Action: MAP0210 General problem resolution. |
| 733-150
to 733-169 |
733
media |
The Test Unit Ready command failed, or the Send Diagnostic command failed. Action: MAP0210 General problem resolution. |
| 733-170 | 733
B88 media |
The Read, Write and Compare test failed. Action: MAP0210 General problem resolution. |
| 733-180
to 733-185 |
733
media |
The Load command failed, or the Unload command failed. Action: MAP0210 General problem resolution. |
| 733-190 | 733 | The Mode Select command failed. Action: MAP0210 General problem resolution. |
| 733-200 | 733
media |
The Test Unit Ready command failed. Action: MAP0210 General problem resolution. |
| 733-210 | 733
B88 |
The device configuration failed. Action: MAP0210 General problem resolution. |
| 733-220
to 733-240 |
733 | 140 GB 8 mm tape drive failed. Action: MAP0210 General problem resolution. |
| 733-300 | 733
software |
The device configuration failed. Action: MAP0210 General problem resolution. |
| 733-310 | B88
733 software |
SCSI adapter configuration failed. Action: MAP0210 General problem resolution. |
| 733-320 | 733
media |
Error log analysis indicates a failure. Action: MAP0210 General problem resolution. |
| 733-411
to 733-423 |
733
B88 software |
A reservation conflict occurred. Action: MAP0210 General problem resolution. |
| 733-511
to 733-523 |
733
B88 |
The drive returned bad or non-extended sense data. Action: MAP0210 General problem resolution. |
| 733-611
to 733-723 |
733
B88 software |
An adapter, device, or bus I/O error occurred. Action: MAP0210 General problem resolution. |
| 736-101 | 821 | An unexpected adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-102 | 736
821 |
An unexpected device or adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-103 | 736
821 |
The keyboard reset failed. Action: MAP0210 General problem resolution. |
| 736-104 | 736 | Unknown keyboard. Action: MAP0210 General problem resolution. |
| 736-105 | 736
821 |
The keyboard light-on test failed. Action: MAP0210 General problem resolution. |
| 736-106 | 736
821 |
The keyboard light-off test failed. Action: MAP0210 General problem resolution. |
| 736-201 | 821 | An unexpected adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-202 | 736
821 |
An unexpected device or adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-203 | 736
821 |
The read keyboard ID test failed. Action: MAP0210 General problem resolution. |
| 736-204 | 736 | The keyboard layout ID test failed. Action: MAP0210 General problem resolution. |
| 736-205 | 736
821 |
The keyboard echo test failed. Action: MAP0210 General problem resolution. |
| 736-206 | 736
821 |
The select scan code set test failed. Action: MAP0210 General problem resolution. |
| 736-301 | 821 | An unexpected adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-302 | 736
821 |
An unexpected device or adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-303 | 736 | An error occurred in turning on the lamps. Action: MAP0210 General problem resolution. |
| 736-304 | 736 | An error occurred in turning off the lamps. Action: MAP0210 General problem resolution. |
| 736-401 | 821 | An unexpected adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-402 | 736
821 |
An unexpected device or adapter error occurred. Action: MAP0210 General problem resolution. |
| 736-403 | 736 | Unable to recognize the keyboard. Action: MAP0210 General problem resolution. |
| 736-404 | 736
821 |
The keyboard is failing. Action: MAP0210 General problem resolution. |
| 736-701 | 736
821 |
Error configuring the device. Action: MAP0210 General problem resolution. |
| 736-901 | 821 | The error log analysis indicates an adapter failure. Action: MAP0210 General problem resolution. |
| 736-902 | 736
821 |
The error log analysis indicates a device failure. Action: MAP0210 General problem resolution. |
| 736-903 | 736
821 |
The error log analysis indicates an unknown failure. Action: MAP0210 General problem resolution. |
| 741-xxx | See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 742-101 | 742 | Configuration register test failed. Action: MAP0210 General problem resolution |
| 742-102 | 742 | I/O register test failed. Action: MAP0210 General problem resolution |
| 742-104 | 742 | Internal loopback test failed. Action: MAP0210 General problem resolution |
| 742-105 | 742 | Internal loopback test failed. Action: MAP0210 General problem resolution |
| 742-106 | 742 | External loopback test failed. Action: MAP0210 General problem resolution |
| 742-121 | D59 | Configuration register test failed. Action: MAP0210 General problem resolution |
| 742-122 | D59 | I/O register test failed. Action: MAP0210 General problem resolution |
| 742-124 | D59 | Internal loopback test failed. Action: MAP0210 General problem resolution |
| 742-125 | D59 | Internal loopback test failed. Action: MAP0210 General problem resolution |
| 742-126 | D59 | External loopback test failed. Action: MAP0210 General problem resolution |
| 742-141 | D60 | Configuration register test failed. Action: MAP0210 General problem resolution |
| 742-142 | D60 | I/O register test failed. Action: MAP0210 General problem resolution |
| 742-144 | D60 | Internal loopback test failed. Action: MAP0210 General problem resolution |
| 742-145 | D60 | Internal loopback test failed. Action: MAP0210 General problem resolution |
| 742-160 | B08 | 10Base-T transceiver test failed. Action: MAP0210 General problem resolution |
| 742-161 | B09 | 10Base-2 transceiver test failed. Action: MAP0210 General problem resolution |
| 742-203 | 742
software |
Device configuration failed. Action: MAP0210 General problem resolution |
| 742-223 | D59
software |
Device configuration failed. Action: MAP0210 General problem resolution |
| 742-224 | B08
D59 |
10 Base-T transceiver test failed. Action: MAP0210 General problem resolution |
| 742-225 | B09
D59 |
10 Base-2 transceiver test failed. Action: MAP0210 General problem resolution |
| 742-243 | D60
software |
Device configuration failed. Action: MAP0210 General problem resolution |
| 742-700 | 742
software |
Error log analysis indicates a hardware problem. Action: MAP0210 General problem resolution |
| 742-720 | D59
software |
Error log analysis indicates a hardware problem. Action: MAP0210 General problem resolution |
| 742-740 | D60
software |
Error log analysis indicates a hardware problem. Action: MAP0210 General problem resolution |
| 745-100 | media
745 |
Recovered error. Action: No action required. |
| 745-200 | media
745 |
Drive Not Ready. Action: Install media, refer to the tape autoloader service information. |
| 745-300
to 745-350 |
media
745 |
4-mm Tape Auto Loader problem. Action: Replace media, clean drive, refer to the tape autoloader service information. |
| 745-400 | 745
magazine media |
General Hardware Failure. Action: Replace media, clean drive, refer to the tape autoloader service information. |
| 745-410
to 745-435 |
745
media |
Internal Hardware Failure Action: Replace drive, refer to the tape autoloader service information. |
| 745-440 | 745
SCSI Adapter |
SCSI Hardware Failure. Action: Replace drive, refer to the tape autoloader service information. |
| 745-441
to 745-443 |
745
media |
4-mm Tape Auto Loader problem. Action: Replace drive, refer to the tape autoloader service information. |
| 745-444 | 745
environ- ment media |
Humidity too High Action: Lower humidity, replace media, refer to the tape autoloader service information. |
| 745-445 | clean media drive | Drive Requires Cleaning Action: Clean drive, replace media, refer to the tape autoloader service information. |
| 745-460 to 745-465 | 745
magazine media |
Magazine Movement Failure Action: Check magazine and media, clean rollers, refer to the tape autoloader service information. |
| 745-470
to 745-475 |
745
magazine media |
Media Insert/Eject Failure Action: Check clean magazine and media, clean rollers, refer to the tape autoloader service information. |
| 745-480
to 745-485 |
745
magazine media |
Drawer Open/Close Failure Action: Check magazine and media, refer to the tape autoloader service information. |
| 745-500 | 745
system |
Illegal request to drive Action: Software conflict, refer to the tape autoloader service information. |
| 745-600 | 745
system |
Unit Attention Action: Software conflict, media changed, refer to the tape autoloader service information. |
| 745-700 | 745
media |
Not Writeable Action: Check media for write-protect, refer to the tape autoloader service information. |
| 745-800 | 745
media |
Blank Media Action: Check media, refer to the tape autoloader service information. |
| 745-B00 | 745
SCSI Adapter |
SCSI Interface Failure Action: Check SCSI interface, refer to the tape autoloader service information. |
| 745-D00 | 745
media |
Tape Full Action: Check replace media, refer to the tape autoloader service information. |
| 746-101
|
221 | Enhanced error handling failure on the bus. Action: MAP0210 General problem resolution |
| 746-102
|
293 | Enhanced error handling failure on a PCI-PCI Bridge. Action: MAP0210 General problem resolution |
| 746-103
|
746
221 |
Enhanced error handling failure on the adapter. Action: MAP0210 General problem resolution |
| 746-212 | 746 | FIFO empty bit set. Action: MAP0210 General problem resolution |
| 746-213 | 746 | FIFO empty bit clear. Action: MAP0210 General problem resolution |
| 746-214 | 746 | FIFO full bit set. Action: MAP0210 General problem resolution |
| 746-215 | 746 | FIFO full bit clear. Action: MAP0210 General problem resolution |
| 746-216 | 746 | FIFO data miscompare. Action: MAP0210 General problem resolution |
| 746-217 | 746 | SCSI FIFO data miscompare. Action: MAP0210 General problem resolution |
| 746-218 | 746 | SCSI FIFO underflow. Action: MAP0210 General problem resolution |
| 746-219 | SCSI parity error. Action: MAP0050 SCSI bus problems | |
| 746-220 | 746 | SCSI FIFO flags error. Action: MAP0210 General problem resolution |
| 746-221 | 746
221 |
Miscompare during the write/read of the configuration register. Action: MAP0210 General problem resolution |
| 746-222 | 746 | Error during the write/read of the memory register. Action: MAP0210 General problem resolution |
| 746-223
|
746
|
Miscompare during the write/read of the memory I/O register. Action: MAP0050 SCSI bus problems |
| 746-224 | 746
221 |
SCSI configuration register read or write error. Action: MAP0210 General problem resolution |
| 746-225 | 746 | Adapter POST failed. Action: MAP0210 General problem resolution |
| 746-226 | SCSI wrap or PTC failure. Action: MAP0050 SCSI bus problems | |
| 746-227
|
746
221 |
SCSI adapter test failure. Action: MAP0210 General problem resolution |
| 746-230 | Arbitration test failed. Action: MAP0050 SCSI bus problems | |
| 746-231 | Function could not complete. Action: MAP0050 SCSI bus problems | |
| 746-232 | SCSI bus data miscompare. Action: MAP0050 SCSI bus problems | |
| 746-240 | No terminal power. Action: MAP0050 SCSI bus problems | |
| 746-242 | SCSI bus error. Action: MAP0050 SCSI bus problems | |
| 746-301 | 746
221 |
The parent device open failed. Action: MAP0210 General problem resolution |
| 746-701 | 746 | Error log analysis indicates a PCI SCSI adapter failure. Action: MAP0210 General problem resolution |
| 746-801 | Error log analysis indicates a terminator problem. Action: Run the diagnostics on the adapter in system verification mode. If an SRN is reported, use the SRN to resolve the problem. If an SRN is not reported, use the SCSI service hints in General SCSI configuration checks to resolve the problem. | |
| 746-802 | Error log analysis indicates that multiple attempts to reset the SCSI bus have timed out. Action: Run the diagnostics on the adapter in System Verification mode. If an SRN is reported, use the SRN to resolve the problem. If an SRN is not reported, use the SCSI service hints in General SCSI configuration checks to resolve the problem. | |
| 746-803 | Error log analysis indicates that multiple SCSI bus errors have occurred. Action: Run the diagnostics on the adapter in system verification mode. If an SRN is reported, use the SRN to resolve the problem. If an SRN is not reported, use the SCSI service hints in General SCSI configuration checks to resolve the problem. | |
| 747-101 | 221 | Enhanced error handling failure on the bus. Action: MAP0210 General problem resolution |
| 747-102 | 293 | Enhanced error handling failure on a PCI-PCI Bridge. Action: MAP0210 General problem resolution |
| 747-103 | 747
221 |
Enhanced error handling failure on the adapter. Action: MAP0210 General problem resolution |
| 747-212 | 747 | FIFO empty bit set. Action: MAP0210 General problem resolution |
| 747-213 | 747 | FIFO empty bit clear. Action: MAP0210 General problem resolution |
| 747-214 | 747 | FIFO full bit set. Action: MAP0210 General problem resolution |
| 747-215 | 747 | FIFO full bit clear. Action: MAP0210 General problem resolution |
| 747-216 | 747 | FIFO data miscompare. Action: MAP0210 General problem resolution |
| 747-217 | 747 | SCSI FIFO data miscompare. Action: MAP0210 General problem resolution |
| 747-218 | 747 | SCSI FIFO underflow. Action: MAP0210 General problem resolution |
| 747-219 | SCSI parity error. Action: MAP0050 SCSI bus problems | |
| 747-220 | 747 | SCSI FIFO flags error. Action: MAP0210 General problem resolution |
| 747-221 | 747
221 |
Miscompare during the write/read of the configuration register. Action: MAP0210 General problem resolution |
| 747-222 | 747 | Error during the write/read of the memory register. Action: MAP0210 General problem resolution |
| 747-223 | 747 | Miscompare during the write/read of the memory I/O register. Action: MAP0050 SCSI bus problems |
| 747-224 | 747
221 |
SCSI configuration register read or write error. Action: MAP0210 General problem resolution |
| 747-225 | 747 | Adapter POST failed. Action: MAP0210 General problem resolution |
| 747-226 | SCSI wrap or PTC failure. Action: MAP0050 SCSI bus problems | |
| 747-227 | 747
221 |
SCSI adapter test failure. Action: MAP0210 General problem resolution |
| 747-230 | Arbitration test failed. Action: MAP0050 SCSI bus problems | |
| 747-231 | Function could not complete. Action: MAP0050 SCSI bus problems | |
| 747-232 | SCSI bus data miscompare. Action: MAP0050 SCSI bus problems | |
| 747-240 | No terminal power. Action: MAP0050 SCSI bus problems | |
| 747-242 | SCSI bus error. Action: MAP0050 SCSI bus problems | |
| 747-301 | 747
221 |
The parent device open failed. Action: MAP0210 General problem resolution |
| 747-701 | 747 | Error log analysis indicates a PCI SCSI adapter failure. Action: MAP0210 General problem resolution |
| 747-801
|
Error log analysis indicates a terminator problem. Action: Run the diagnostics on the adapter in system verification mode. If an SRN is reported, use the SRN to resolve the problem. If an SRN is not reported, use the SCSI service hints in General SCSI configuration checks to resolve the problem. | |
| 747-802
|
Error log analysis indicates that multiple attempts to reset the SCSI bus have timed out. Action: Run the diagnostics on the adapter in system verification mode. If an SRN is reported, use the SRN to resolve the problem. If an SRN is not reported, use the SCSI service hints in General SCSI configuration checks to resolve the problem. | |
| 747-803
|
Error log analysis indicates that multiple SCSI bus errors have occurred. Action: Run the diagnostics on the adapter in system verification mode. If an SRN is reported, use the SRN to resolve the problem. If an SRN is not reported, use the SCSI service hints in General SCSI configuration checks to resolve the problem. | |
| 749-xxx | 749 | 7331 Model 205 Tape Library. Refer to service documentation for this device. |
| 757-110 | 757 | The Reserve command failed. Action: MAP0210 General problem resolution |
| 757-120 | 757 | The Inquiry command failed. Action: MAP0210 General problem resolution |
| 757-130 | 757
media |
The Load command failed. Action: MAP0210 General problem resolution |
| 757-135 | 757
media |
The Unload command failed. Action: MAP0210 General problem resolution |
| 757-140 | 757 | The Mode Select command failed. Action: MAP0210 General problem resolution |
| 757-150 | 757
media |
The Test Unit Ready command failed. Action: MAP0210 General problem resolution |
| 757-160 | 757
media |
The Send Diagnostic command failed. Action: MAP0210 General problem resolution |
| 757-169 | 757
media |
The Send Diagnostic command failed. Action: MAP0210 General problem resolution |
| 757-170 | 757
B88 media |
The Read, Write and Compare test failed. Action: MAP0210 General problem resolution |
| 757-180 | 757
media |
The Load command failed. Action: MAP0210 General problem resolution |
| 757-185 | 757
media |
The Unload command failed. Action: MAP0210 General problem resolution |
| 757-190 | 757 | The Mode Select command failed. Action: MAP0210 General problem resolution |
| 757-200 | 757
media |
The Test Unit Ready command failed. Action: MAP0210 General problem resolution |
| 757-210 | 757
B88 |
The device configuration failed. Action: MAP0210 General problem resolution |
| 757-220 | 757 | The Release command failed. Action: MAP0210 General problem resolution |
| 757-230 | 757 | The Request Sense command failed. Action: MAP0210 General problem resolution |
| 757-240 | 757 | The Openx command failed. Action: MAP0210 General problem resolution |
| 757-300 | 757
software |
The device configuration failed. Action: MAP0210 General problem resolution |
| 757-310 | B88
757 software |
SCSI adapter configuration failed. Action: MAP0210 General problem resolution |
| 757-320 | 757
media |
Error log analysis indicates a failure. Action: MAP0210 General problem resolution |
| 757-411 to 757-423 | 757
B88 software |
A reservation conflict occurred. Action: MAP0210 General problem resolution |
| 757-511
to 757-523 |
757
B88 |
The drive returned bad or non-extended sense data. Action: MAP0210 General problem resolution |
| 757-611
to 757-623 |
757
B88 software |
An adapter or bus I/O error occurred. Action: MAP0210 General problem resolution |
| 757-711
to 757-723 |
757
B88 software |
A device timeout error occurred. Action: MAP0210 General problem resolution |
| 759-xxx | See. Action: MAP0210 General problem resolution | |
| 763-1xx | 763
software 221 |
Problem detected with a device or device data corrupted. Note: You
might need to reinstall ssp.css software.
|
| 763-200
to 763-299 |
ext clock
763 wrap plug |
Problem detected with the external clock (SP switch). Notes:
|
| 763-2A0
to 763-2A9 |
763 | Problem detected with the internal clock. Action: MAP0210 General problem resolution |
| 763-3xx | 763
221 |
Problem detected with the POS registers. Action: MAP0210 General problem resolution |
| 763-4xx | 763
software |
TBIC test failed. Action: MAP0210 General problem resolution |
| 763-5xx | 763 | SRAM test failed. Action: MAP0210 General problem resolution |
| 763-6xx | 763 | Microprocessor test failed. Action: MAP0210 General problem resolution |
| 763-7xx | 763 | Interrupt test failed. Action: MAP0210 General problem resolution |
| 763-8xx | 763 | FIFO test failed. Action: MAP0210 General problem resolution |
| 763-9xx | 763
221 Switch- cable |
DMA engine test failed. Note: Refer to your SP Maintenance
Information for the switch cable FRU part number.
|
| 763-Ax3 | 763
terminator |
Card wrap test failed. Note: The terminator FRU part number
is listed under the 763 FFC.
Action: MAP0210 General problem resolution |
| 763-Ax4 | Switch-
cable wrap plug |
Card wrap test failed. Notes:
|
| 763-xx2 | 763 | Bad adapter card. (except for SRN 763-282) Action: Replace the SP Switch MX Adapter. |
| 764-1xx | 764
software 221 |
Problem detected with a device or device data corrupted. Note: You
might need to reinstall ssp.css software.
|
| 764-200 to 764-299 | ext clock
764 wrap plug |
Problem detected with the external clock (SP switch). Notes:
|
| 764-2A0
to 764-2A9 |
764 | Problem detected with the internal clock. Action: MAP0210 General problem resolution |
| 764-3xx | 764
221 |
Problem detected with the POS registers. Action: MAP0210 General problem resolution |
| 764-4xx | 764
software |
TBIC test failed. Action: MAP0210 General problem resolution |
| 764-5xx | 764 | SRAM test failed. Action: MAP0210 General problem resolution |
| 764-6xx | 764 | Microprocessor test failed. Action: MAP0210 General problem resolution |
| 764-7xx | 764 | Interrupt test failed. Action: MAP0210 General problem resolution |
| 764-8xx | 764 | FIFO test failed. Action: MAP0210 General problem resolution |
| 764-9xx | 764
221 switch- cable |
DMA engine test failed. Note: Refer to your SP Maintenance
Information for the switch cable FRU part number.
|
| 764-Ax3 | 764
terminator |
Card wrap test failed. Note: The terminator FRU part number
is listed under the 763 FFC.
|
| 764-Ax4 | Switch-
cable wrap plug |
Card wrap test failed. Notes:
|
| 764-xx2 | 764 | Bad adapter card. (except for SRN 764-282) Action: Replace the SP Switch MX Adapter. |
| 772-xxx
to 774-xxx |
See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 776-101 | D46 | External Test Failure. Action: MAP0210 General problem resolution |
| 776-102 | 240 | External Test Failure. Action: MAP0210 General problem resolution |
| 776-103 | 776 | I/O Test Failure. Action: MAP0210 General problem resolution |
| 776-104 | 776
221 |
Adapter On-card Test Failure. Action: MAP0210 General problem resolution |
| 776-105 | 776 | Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-106 | D46 | Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-106 | 776 | Enhanced error handling failure on bus. Action: MAP0210 General problem resolution |
| 776-107 | 776 | Enhanced error handling failure on Eads chip. Action: MAP0210 General problem resolution |
| 776-108 | 776 | Enhanced error handling failure on adapter. Action: MAP0210 General problem resolution |
| 776-201 | 776
221 |
Configuration Register Test Failure. Action: MAP0210 General problem resolution |
| 776-202 | 776
221 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-203 | D46
776 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-204 | 776
221 |
Connect Test Failure. Action: MAP0210 General problem resolution |
| 776-205 | D46
776 |
External Test Failure. Action: Run advanced diagnostics with wrap test for this resource to obtain correct problem isolation. Action: MAP0210 General problem resolution |
| 776-206 | 776
221 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-301 | D46
240 776 |
External Test Failure. Action: MAP0210 General problem resolution |
| 776-302 | D46
776 221 |
External Test Failure. Action: Run advanced diagnostics with wrap test for this resource to obtain correct problem isolation. |
| 776-303 | 240
D46 776 |
External Test Failure. Action: Run advanced diagnostics with wrap test for this resource to obtain correct problem isolation. |
| 776-304 | D46
776 221 |
Connect Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-305 | D46
776 221 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-306 | D46
776 221 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-401 | 240
D46 776 221 |
External Test Failure. Action: Run advanced diagnostics with wrap test for this resource to obtain correct problem isolation. |
| 776-404 | 240
D46 776 221 |
Connect Test Failure. Action: MAP0210 General problem resolution |
| 776-405 | 240
D46 776 221 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-406 | 240
D46 776 221 |
Wrap Test Failure. Action: MAP0210 General problem resolution |
| 776-414 | 240
D46 776 221 |
Connect Test Failure. This failure occurs if not connected to a functional Token-Ring network. Action: Run advanced diagnostics for this resource to obtain correct problem isolation. |
| 776-415 | 240
D46 776 221 |
Wrap Test Failure. This failure occurs if not connected to a functional Token-Ring network. Action: Run advanced diagnostics for this resource to obtain correct problem isolation. |
| 776-416 | 240
D46 776 221 |
Wrap Test Failure. This failure occurs if not connected to a functional Token-Ring network. Action: Run advanced diagnostics for this resource to obtain correct problem isolation. |
| 776-701 | 776 | ELA indicates an adapter error occurred. Action: MAP0210 General problem resolution |
| 776-702 | 776
221 |
ELA indicates an adapter check occurred. Action: MAP0210 General problem resolution |
| 776-703 | 776
221 |
ELA indicates a DMA failure occurred. Action: MAP0210 General problem resolution |
| 776-704 | 776
221 |
ELA indicates a PCI bus failure occurred. Action: MAP0210 General problem resolution |
| 776-705 | 776
221 |
ELA indicates a Programmed I/O failure occurred. Action: MAP0210 General problem resolution |
| 776-706 | 776 | ELA indicates a command write failure occurred. Action: MAP0210 General problem resolution |
| 776-707 | 776 | ELA indicates an internal adapter error has occurred. Action: MAP0210 General problem resolution |
| 778-002 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-004 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-009 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-011 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-017 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-019 | 778
software |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-030 | 778
221 |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-032 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-033 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-035 | 778
software |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-036
to 778-072 |
software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-073 | 778
221 |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-075 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-076 | 778
software |
Software error. Action: MAP0210 General problem resolution |
| 778-301
to 778-D02 |
778
221 |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-E01 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-E02
to 778-1401 |
778
221 |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-1402 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-1403
to 778-1405 |
778
221 |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-1500 | 778
software |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-1600
to 778-1604 |
778
902 |
Adapter failure. Action: MAP0210 General problem resolution |
| 778-2501
to 778-2508 |
778
221 |
Adapter error. Action: MAP0210 General problem resolution |
| 778-2509
to 778-2511 |
software
778 |
Software error. Action: MAP0210 General problem resolution |
| 778-2601
to 778-2602 |
778
221 |
Adapter error. Action: MAP0210 General problem resolution |
| 778-2603 | software
778 |
Software error. Action: MAP0210 General problem resolution |
| 77C-xxx | See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 780-101 | 780
227 |
Adapter logic test failure. Action: MAP0210 General problem resolution |
| 780-102 | 780 | Adapter logic test failure. Action: MAP0210 General problem resolution |
| 780-109 | 780 | Adapter channel Input/Output test failure. Action: MAP0210 General problem resolution |
| 780-113 | 780 | Adapter Serial Communication Controller (SCC) test failure. Action: MAP0210 General problem resolution |
| 780-114 | 780
227 |
Adapter logic test failure. Action: MAP0210 General problem resolution |
| 780-120 | 780
227 software |
Adapter could not be detected or configured. Action: MAP0210 General problem resolution |
| 780-140 | 271
780 |
An error was found with the X.21 interface adapter cable. Action: MAP0210 General problem resolution |
| 780-150 | 272
780 |
An error was found with the X.24 interface adapter cable. Action: MAP0210 General problem resolution |
| 780-160 | 273
780 |
An error was found with the X.35 interface adapter cable. Action: MAP0210 General problem resolution |
| 780-170 | 780 | The adapter hardware failed. Action: MAP0210 General problem resolution |
| 780-180 | 780 | The adapter hardware failed. Action: MAP0210 General problem resolution |
| 780-190 | 780 | The adapter hardware failed. Action: MAP0210 General problem resolution |
| 780-210 | 780
185 |
An error was found on the adapter. Action: MAP0210 General problem resolution |
| 780-211 | 780
227 |
The adapter card POST test failed. Action: MAP0210 General problem resolution |
| 780-230 | 780 | The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-232 | 780
227 |
The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-240 | 780 | The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-250 | 185
780 |
An error was found on the adapter. Action: MAP0210 General problem resolution |
| 780-260 | 780 | The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-270 | 780 | The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-280 | 780 | The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-290 | 780 | The adapter card hardware failed. Action: MAP0210 General problem resolution |
| 780-300 | 780 | An adapter error was found during error log analysis. Action: MAP0210 General problem resolution |
| 780-310 | 780
185 |
An adapter error was found during error log analysis. Action: MAP0210 General problem resolution |
| 780-320 | 780
227 |
An adapter error was found during error log analysis. Action: MAP0210 General problem resolution |
| 780-330 | 780
227 |
Error log analysis indicates a hardware problem. Action: MAP0210 General problem resolution |
| 780-400 | 780
227 |
A software error was caused by a hardware failure. Action: MAP0210 General problem resolution |
| 780-700 | 780
227 software |
The adapter failed to configure. Action: MAP0210 General problem resolution |
| 780-720 | 780 | Cable wrap test failed. Action: MAP0210 General problem resolution |
| 780-721 | 780 | Port wrap test failed. Action: MAP0210 General problem resolution |
| 780-722 | 780 | Cable wrap test failed. Action: MAP0210 General problem resolution |
| 781-101 | 781
227 |
ROS POST adapter software initialization error. Action: MAP0210 General problem resolution |
| 781-102 | 781 | Extended DRAM SIP test failed. Action: MAP0210 General problem resolution |
| 781-103 | 781 | ROS checksum test failed. Action: MAP0210 General problem resolution |
| 781-104 | 781
227 |
Adapter download diagnostics failed Action: MAP0210 General problem resolution |
| 781-105 | 781
227 |
Memory size test failed. Action: MAP0210 General problem resolution |
| 781-106 | 781
227 |
Interface ID test failed. Action: MAP0210 General problem resolution |
| 781-107 | 781
227 |
EIB ID test failed. Action: MAP0210 General problem resolution |
| 781-108 | 781
227 |
ROS version test failed. Action: MAP0210 General problem resolution |
| 781-109 | 781 | DUSCC register test failed. Action: MAP0210 General problem resolution |
| 781-111 | 781 | DMA register test failed. Action: MAP0210 General problem resolution |
| 781-112 | 781 | X.21 PAL test failed. Action: MAP0210 General problem resolution |
| 781-113 | 781 | External wrap test failed. Action: MAP0210 General problem resolution |
| 781-114 | 781
227 |
Twin tail logic test failed. Action: MAP0210 General problem resolution |
| 781-116 | 254 | The RS232 cable wrap test failed. Action: MAP0210 General problem resolution |
| 781-117 | 253 | The RS422A cable wrap test failed. Action: MAP0210 General problem resolution |
| 781-118 | 257 | The V.35 cable wrap test failed. Action: MAP0210 General problem resolution |
| 781-119 | 260 | The X.21 cable wrap test failed. Action: MAP0210 General problem resolution |
| 781-120 | 781
227 software |
The adapter was not detected or could not be configured. test failed. Action: MAP0210 General problem resolution |
| 781-121 | 781
227 software |
The 4-port jumper cable assembly wrap test failed. Action: MAP0210 General problem resolution |
| 781-200 | 781 | The error log analysis indicates the adapter failed. Action: MAP0210 General problem resolution |
| 781-221 | 781
227 |
The error log analysis indicates the adapter hardware failed. Action: MAP0210 General problem resolution |
| 781-231 | 227
|
No interface card detected. Action: MAP0210 General problem resolution |
| 781-501 | B77
B69 227 |
The power-on self-test (POST) failed. Action: MAP0210 General problem resolution |
| 781-502 | B77 | The memory module failed. Action: MAP0210 General problem resolution |
| 781-503 | 781
227 |
Adapter hardware failure. Action: MAP0210 General problem resolution |
| 781-504 | B69 | Adapter hardware failure. Action: MAP0210 General problem resolution |
| 781-505 | B71
B69 |
Adapter hardware failure. Action: MAP0210 General problem resolution |
| 781-506 | B72
B69 |
Adapter hardware failure. Action: MAP0210 General problem resolution |
| 781-507 | B73
B69 |
Adapter hardware failure. Action: MAP0210 General problem resolution |
| 781-508 | B74
B69 |
Adapter hardware failure. Action: MAP0210 General problem resolution |
| 781-516 | B77
B69 |
Adapter Test Failure. Action: MAP0210 General problem resolution |
| 781-517 | B69
B77 |
Adapter Test Failure. Action: MAP0210 General problem resolution |
| 781-720 | 258
781 |
4-port multiprotocol cable Action: MAP0210 General problem resolution |
| 783-110 | 783 | The Reserve command failed. Action: MAP0210 General problem resolution |
| 783-120 | 783 | The Inquiry command failed. Action: MAP0210 General problem resolution |
| 783-130 | 783
media |
The Load command failed. Action: MAP0210 General problem resolution |
| 783-135 | 783
media |
The Unload command failed. Action: MAP0210 General problem resolution |
| 783-140 | 783 | The Mode Select command failed. Action: MAP0210 General problem resolution |
| 783-150 | 783
media |
The Test Unit Ready command failed. Action: MAP0210 General problem resolution |
| 783-160 | 783
media |
The Send Diagnostic command failed. Action: MAP0210 General problem resolution |
| 783-169 | 783
media |
The Send Diagnostic command failed. Action: MAP0210 General problem resolution |
| 783-170 | 783
B88 media |
The Read, Write and Compare test failed. Action: MAP0210 General problem resolution |
| 783-180 | 783
media |
The Load command failed. Action: MAP0210 General problem resolution |
| 783-185 | 783
media |
The Unload command failed. Action: MAP0210 General problem resolution |
| 783-190 | 783 | The Mode Select command failed. Action: MAP0210 General problem resolution |
| 783-200 | 783
media |
The Test Unit Ready command failed. Action: MAP0210 General problem resolution |
| 783-210 | 783
B88 |
The device configuration failed. Action: MAP0210 General problem resolution |
| 783-220 | 783 | The Release command failed. Action: MAP0210 General problem resolution |
| 783-230 | 783 | The Request Sense command failed. Action: MAP0210 General problem resolution |
| 783-240 | 783 | The Openx command failed. Action: MAP0210 General problem resolution |
| 783-300 | 783
software |
The device configuration failed. Action: MAP0210 General problem resolution |
| 783-310 | B88
783 software |
SCSI adapter configuration failed. Action: MAP0210 General problem resolution |
| 783-320 | 783
media |
Error log analysis indicates a failure. Action: MAP0210 General problem resolution |
| 783-411
to 783-423 |
783
B88 software |
A reservation conflict occurred. Action: MAP0210 General problem resolution |
| 783-511
to 783-523 |
783
B88 |
The drive returned bad or non-extended sense data. Action: MAP0210 General problem resolution |
| 783-611
to 783-623 |
783
B88 software |
An adapter or bus I/O error occurred. Action: MAP0210 General problem resolution |
| 783-711
to 783-723 |
783
B88 software |
A device timeout error occurred. Action: MAP0210 General problem resolution |
| 784-xxx | See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 785-111 | 785
227 |
Could not do the test because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-114 | 785 | The register verification test failed. Action: MAP0210 General problem resolution |
| 785-121 | 785
227 |
Could not do the test because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-122 | 785
227 |
The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-123 | 785
227 |
The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-124 | 785 | The memory test failed. Action: MAP0210 General problem resolution |
| 785-151 | 785
D57 |
Could not do the test because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-152 | 785
D57 |
The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-153 | 785
D57 |
The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-171 | 259 | Could not do the test because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-172 | 259 | The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-173 | 259 | The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-181 | 261 | Could not do the test because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-182 | 261 | The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-183 | 261 | The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-251 | 785
D57 |
Could not perform because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-252 | 785
D57 |
The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-253 | 785
D57 |
The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-271 | 785
D57 |
Could not perform because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-272 | 785
D57 |
The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-273 | 785
D57 |
The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-281 | 785
D57 |
Could not perform because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-282 | 785
D57 |
The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-283 | 785
D57 |
The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-481 | D57 | Could not do the test because the device driver detected a hardware error. Action: MAP0210 General problem resolution |
| 785-482 | D57 | The data wrap communication test failed. Action: MAP0210 General problem resolution |
| 785-483 | D57 | The modem control line test failed. Action: MAP0210 General problem resolution |
| 785-901
to 785-920 |
software
785 |
An unexpected error occurred that can be attributed to software or hardware. Action: Run diagnostics from a source other than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, MAP0210 General problem resolution with a FFC of 785; otherwise, suspect a software problem. |
| 785-921 | 785
software |
The adapter failed to configure. Action: MAP0210 General problem resolution |
| 785-922
to 785-924 |
software
785 |
An unexpected error occurred that can be attributed to software or hardware. Action: Run diagnostics from a source other than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, MAP0210 General problem resolution with a FFC of 785; otherwise, suspect a software problem. |
| 785-925 | 785
software |
The adapter failed to configure. Action: MAP0210 General problem resolution |
| 785-926
to 785-943 |
software
785 |
An unexpected error occurred that can be attributed to software or hardware. Action: Run diagnostics from a source other than from the disk or a network. If the same error occurs or if the original SRN was not obtained from disk or a network based diagnostics, MAP0210 General problem resolution with a FFC of 785; otherwise, suspect a software problem. |
| 786-200 | 786
D96 227 |
Initiation failed. Note: You must determine which of the
first two FFCs is installed in the system unit.
Action: MAP0210 General problem resolution |
| 786-210 | 786
227 |
The adapter test failed. Action: MAP0210 General problem resolution |
| 786-211 | D96
227 |
The adapter test failed. Action: MAP0210 General problem resolution |
| 786-220 | 786
Cable Monitor |
The display test failed. Action: MAP0210 General problem resolution |
| 786-221 | D96
Cable Monitor |
The display test failed. Action: MAP0210 General problem resolution |
| 786-710 | 786
227 |
The ELA indicates HW failure. Action: MAP0210 General problem resolution |
| 786-711 | D96
227 |
The ELA indicates HW failure. Action: MAP0210 General problem resolution |
| 787-100 | 787 | GXT500P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-101 | 787
227 |
GXT500P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-1AA | 787
RGB Cable Display |
GXT500P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-1xx | 787 | GXT500P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-200 | D95 | GXT550P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-201 | D95
227 |
GXT550P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-2AA | D95
RGB Cable Display |
GXT550P Graphics Adapter. Action: MAP0210 General problem resolution |
| 787-2xx | D95 | GXT550P Graphics Adapter. Action: MAP0210 General problem resolution |
| 788-001 | 788
227 |
Adapter Error. Action: MAP0210 General problem resolution |
| 788-002 | software
788 |
System Error. Action: MAP0210 General problem resolution |
| 788-003 | software
788 |
System Error. Action: MAP0210 General problem resolution |
| 788-004 | 788
software |
System Error. Action: MAP0210 General problem resolution |
| 789-101 | 789 | Failed to release the device. Action: MAP0210 General problem resolution |
| 789-102 | 789 | Failed to reserve the device. Action: MAP0210 General problem resolution |
| 789-103 | 789 | The device motor failed to start. Action: MAP0210 General problem resolution |
| 789-104 | 789 | Failed to make the device ready. Action: MAP0210 General problem resolution |
| 789-105 | 789 | Failed to get the inquiry data. Action: MAP0210 General problem resolution |
| 789-106 | 789 | The Prevent Media Removal command failed. Action: MAP0210 General problem resolution |
| 789-107 | 789 | The Allow Media Removal command failed. Action: MAP0210 General problem resolution |
| 789-200 | 789
Optical- Disk |
The optical disk failed to load. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the error reoccurs MAP0210 General problem resolution ; otherwise, replace the media. |
| 789-201 | 789
Optical- Disk |
Failed to unload the optical disk. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the errors reoccur MAP0210 General problem resolution ; otherwise, replace the media. |
| 789-202 | 789
Optical- Disk |
The diagnostic test failed. Action: Change the media. Run diagnostics on the changed media in system verification mode. If errors do not reoccur, replace the media; otherwise, run the drive cleaning procedures if applicable and rerun the diagnostics. If errors reoccur, or the drive does not support the cleaning procedures MAP0210 General problem resolution |
| 789-204 | 789
B88 |
The device failed to configure. Action: MAP0210 General problem resolution |
| 789-205 | 789
Optical- Disk |
The Test Unit Ready command failed. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the error reoccurs, MAP0210 General problem resolution ; otherwise, replace the media. |
| 789-206 | 789
Optical- Disk |
The random write, read and compare test failed. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the errors do not reoccur, replace the media; otherwise, run the drive cleaning procedures if applicable, and rerun diagnostics. If the errors reoccur, or the drive does not support cleaning procedures, MAP0210 General problem resolution |
| 789-207 | 789
Optical- Disk |
A hardware error occurred. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the errors do not reoccur, replace the media; otherwise, run the drive cleaning procedures if applicable, and rerun diagnostics. If the errors reoccur, or the drive does not support cleaning procedures, MAP0210 General problem resolution |
| 789-208 | 789
Optical- Disk |
The Mode Sense command failed. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the errors do not reoccur, replace the media; otherwise, run the drive cleaning procedures if applicable, and rerun diagnostics. If the errors reoccur, or the drive does not support cleaning procedures, MAP0210 General problem resolution |
| 789-209 | 789
Optical- Disk |
The Mode Select command failed. Action: Change the media. Run diagnostics on the changed media in system verification mode. If the errors do not reoccur, replace the media; otherwise, run the drive cleaning procedures if applicable, and rerun diagnostics. If the errors reoccur, or the drive does not support cleaning procedures, MAP0210 General problem resolution |
| 789-300 | 789
B88 software |
A SCSI reservation conflict has occurred. Action: MAP0210 General problem resolution |
| 789-400 | 789
B88 Cables software |
A SCSI command time out has occurred. Action: MAP0210 General problem resolution |
| 789-401 | Optical-
Disk 190 B88 software |
An unknown error has occurred. Action: MAP0210 General problem resolution |
| 789-402 | Optical-
Disk 190 B88 software |
Unit attention condition has occurred. Action: MAP0210 General problem resolution |
| 789-600 | Optical-
Disk |
ELA indicates that the spare sectors on the disk are exhausted.
Action: Backup the media and replace it. Note: Use the time when the error
occurred and the "Spare Sector Availability" service aid to identify the disk
that has the error.
|
| 789-700 | 789
Optical- Disk |
The ELA indicates an equipment error. Action: Run diagnostics in system
verification mode to isolate the problem. If errors are reported, MAP0210 General problem resolution ; otherwise, the error is due to faulty media.
Backup the media and then replace it. Note: Use the time when the error occurred to identify the
faulty media.
|
| 789-701 | Optical-
Disk 789 |
ELA indicates an irrecoverable data error. Action: Run diagnostics in system
verification mode to isolate the problem. If errors are reported, MAP0210 General problem resolution ; otherwise, the error is due to faulty media.
Backup the media and then replace it. Note: Use the time when the error occurred to identify the
faulty media.
|
| 789-702 | 789
B88 Cables |
ELA indicates that the adapter detected an error. Action: Use the 7209 Installation and Service information. If the unit checks out to be good, MAP0210 General problem resolution |
| 78B-001 | Software
78B |
Software error. Action: MAP0210 General problem resolution |
| 78B-002 | 78B
Software |
Adapter failure. Action: MAP0210 General problem resolution |
| 78B-003 | 78B
227 |
Adapter failure. Action: MAP0210 General problem resolution |
| 78B-004 | 78B
Monitor/ Cable |
Adapter or display failure. Action: MAP0210 General problem resolution |
| 78B-005 | 78B
227 Monitor/ Cable |
Adapter failure. Action: MAP0210 General problem resolution |
| 78D-001 | software
78D |
Software error. Action: MAP0210 General problem resolution |
| 78D-002 | 78D
software |
Adapter failure. Action: MAP0210 General problem resolution |
| 78D-003 | 78D
227 |
Adapter failure. Action: MAP0210 General problem resolution |
| 78D-004 | 78D
Monitor/ Cable |
Display failure. Action: MAP0210 General problem resolution |
| 78D-005 | 78D
227 Monitor/ Cable |
Adapter failure. Action: MAP0210 General problem resolution |
| 790-101 | 790 | Configuration Register Test failure. Action: MAP0210 General problem resolution |
| 790-102 | 790 | I/O test failure. Action: MAP0210 General problem resolution |
| 790-103 | 790 | Adapter initialization test failure. Action: MAP0210 General problem resolution |
| 790-104 | 790 | Internal wrap test failure. Action: MAP0210 General problem resolution |
| 790-105 | 790 | Internal wrap test failure. Action: MAP0210 General problem resolution |
| 790-106 | 790 | External wrap (10 Mbps) test failure. Action: MAP0210 General problem resolution |
| 790-107 | 790 | Internal wrap test failure. Action: MAP0210 General problem resolution |
| 790-108 | 790 | External wrap (100 Mbps) test failure. Action: MAP0210 General problem resolution |
| 790-109 | 790 | External wrap (10 Mbps) test failure. Action: MAP0210 General problem resolution |
| 790-121 | 790 | Configuration register test failure. Action: MAP0210 General problem resolution |
| 790-122 | 790 | I/O register test failure. Action: MAP0210 General problem resolution |
| 790-124 | 790 | Internal loopback test failure. Action: MAP0210 General problem resolution |
| 790-125 | 790 | Internal loopback test failure. Action: MAP0210 General problem resolution |
| 790-126 | 790 | External loopback test failure. Action: MAP0210 General problem resolution |
| 790-150 | B08 | 10Base-T transceiver test failure. Action: MAP0210 General problem resolution |
| 790-151 | B09 | 10Base-2 transceiver test failure. Action: MAP0210 General problem resolution |
| 790-223 | 790
software |
Device configuration failure. Action: MAP0210 General problem resolution |
| 790-224 | B08
790 |
10 Base-T transceiver test failure. Action: MAP0210 General problem resolution |
| 790-225 | B09
790 |
10 Base-2 transceiver test failure. Action: MAP0210 General problem resolution |
| 790-250 | B08
790 |
10 Base-T transceiver test failure. Action: MAP0210 General problem resolution |
| 790-251 | B09
790 |
10 Base-2 transceiver test failure. Action: MAP0210 General problem resolution |
| 790-701 | 790 | Error Log Analysis indicates that the adapter is not responding to initialization commands. Action: MAP0210 General problem resolution |
| 790-702 | 790 | Error Log Analysis indicates that the device driver has detected a PIO error which it was unable to correct. Action: MAP0210 General problem resolution |
| 790-703 | 790 | Error Log Analysis indicates that the adapter has been shutdown due to an unrecoverable error. Action: MAP0210 General problem resolution |
| 790-704 | 790 | Error Log Analysis indicates a problem with EEPROM on the adapter. Action: MAP0210 General problem resolution |
| 790-720 | 790
software |
Error log analysis indicates a hardware problem. Action: MAP0210 General problem resolution |
| 791-xxx
to 793-xxx |
See SCSI Devices SRNs (ssss-102 to ssss-640). | |
| 799-101 | 2C3
799 |
External wrap test failed on port 0. Action: MAP0210 General problem resolution |
| 799-102 | 2C3
799 |
External wrap test failed on port 1. Action: MAP0210 General problem resolution |
| 799-201 | 799
227 |
Internal adapter test failed. Action: MAP0210 General problem resolution |
| 799-202 | 799
227 |
External wrap test failed on port 0. Action: MAP0210 General problem resolution |
| 799-203 | 799
227 |
External wrap test failed on port 1. Action: MAP0210 General problem resolution |
| 799-204 | 2C3
799 |
External wrap test failed on port 0. Action: MAP0210 General problem resolution |
| 799-205 | 2C3
799 |
External wrap test failed on port 1. Action: MAP0210 General problem resolution |
| 799-206 | 2C3
799 software |
External wrap test failed on port 0. Action: MAP0210 General problem resolution |
| 799-207 | 2C3
799 software |
External wrap test failed on port 1. Action: MAP0210 General problem resolution |
| 799-301 | 799
227 software |
Internal adapter test failed. Action: MAP0210 General problem resolution |
| 799-302 | 799
227 software |
External wrap test failed on port 0. Action: MAP0210 General problem resolution |
| 799-303 | 799
227 software |
External wrap test failed on port 1. Action: MAP0210 General problem resolution |
| 799-304 | 2C3
799 software |
External wrap test failed on port 0. Action: MAP0210 General problem resolution |
| 799-305 | 2C3
799 software |
External wrap test failed on port 1. Action: MAP0210 General problem resolution |
| 799-700 | 799
software |
Error log analysis indicates a hardware problem. Action: MAP0210 General problem resolution |